Article: RDW on blood tests

Discussion in 'General Health & Wellness' started by TwoCatDoctors, Jan 9, 2011.

  1. TwoCatDoctors

    TwoCatDoctors New Member

    What Is RDW on a Blood Test?
    By Eleanor Jewell, eHow Contributor
    updated: April 27, 2010

    If your physician has diagnosed you with a type of anemia or iron deficiency, than somewhere along the line you must have had a blood test that reflected an abnormal RDW count. Your RDW levels, along with a combination of a few other important blood counts are what helps your physician figure out just what type of anemia you have, and why it has manifested. HIP Health Plan of New York explains that there are more than 400 known types of anemia, which can be further broken down into subgroups relating to blood loss, poor red-cell production, and the demise of red blood cells.

    What Does RDW Stand For?

    1. RDW is the abbreviation for "red blood cell distribution width." According to Lab Tests Online, RDW calculates the varying sizes of red-blood-cell (RBC) volume in a blood sample. An RDW test is usually performed as part of a CBC (complete blood count).

    RDW and MCV

    2. It is virtually impossible to discuss the RDW aspect of a blood test without including MCV. Mean corpuscle value (MCV) goes hand in hand with red-blood cell-distribution width (RDW) in terms of anemia and other hematology disorders, and the values of both are influenced by each other. For instance, low MCV levels in combination with normal RDW may point to chronic disease, while low MCV combined with low RDW can denote iron deficiency. In the same respect, a normal MCV reading in combination with normal RDW may represent a chronic disorder and normal MCV combined with high RDW can signifies a B12 deficiency. Chronolab.com also reveals that when MCV levels are high and RDW is normal, pre-leukemia may be present. Both high MCV and high RDW may mean that a patient is experiencing folate deficiency.

    RDW Calculation

    3. RDW is calculated by dividing the standard deviation (SD) by the mean corpuscle volume (MCV) and then multiplying that result by 100. The standard deviation represents the volume of erythrocytes or red blood cells that are in the blood smear. According to Beckman Coulter, the equation for the RDW calculation is RDW=SD/MCV x 100.

    Normal Reference Range for RDW Blood Test

    4. Normal RDW values are between 11 percent and 14 percent, with an optimum RDW value range of 13 percent. When RDW values rise above normal levels, several disorders become suspect. According to the Archives of Internal Medicine, RDW counts may also play an important role in predicting mortality; especially, in patients who have cardiovascular disease and cancer. In fact, patient's who test higher than the normal reference range on an RDW test may suffer more health risks than those patients whose RDW values are lower.

    Anisocytosis

    5. Anisocytosis is diagnosed when the RDW levels in a blood test indicate excessively high values of variably shaped red blood cells. In the book "Diagnostic Hematology," author Norman Beck explains that the presence of anisocytosis in a diagnostic blood test is so common that it is often dismissed as a component while making a diagnosis. But, recent breakthroughs in medicine have shed new light on the importance of anisocytosis during patient evaluation. When anisocytosis is measured against other blood cells values, the high RBC values can help make a better determination of the type of anemia that is present in the patient.

    Consult Your Health Care Provider

    6. Blood tests and their results are a piece of the overall diagnostic picture and are not meant to be the sole tool used for diagnosis or prognosis of illness. Consulting with your health care provider for a full physical as well as an assessment of symptoms is the best method of understanding your blood test results.

    FROM: http://www.ehow.com/about_5314562_rdw-blood-test_.html